Three members of a design team will probably give you three different answers when you ask about retention basins and detention basins. One thinks it’s the shape. Another thinks it’s whether there’s water in it. The third swears it’s just local wording. All three individuals provide partial truth which creates problems because the selection between these two options determines both the grading process and the financial plan and long-term maintenance requirements. Good stormwater basin design engineering starts by getting the two straight.
What each one actually does
A detention basin slows water down. Runoff enters the area during storms and starts to build up behind a restricted outlet which allows only limited water flow before the water slowly disappears through drainage that takes multiple hours. The ground becomes dry after storms pass through the area. The objective requires you to maintain your site’s existing peak flow rate because any increase would damage the downstream pipe and creek systems.

A retention basin keeps water. The water that runs off from the site will stay in place until it reaches the ground for absorption or until it disappears through evaporation or gets consumed instead of moving toward downstream areas. The area contains two types of water features which include wet ponds that maintain permanent water bodies and infiltration basins that remain dry until they absorb water into the ground.
Different organizations use their own terms to describe things and local authorities call their retention basins what others refer to as infiltration basins. Before you commit to a name on the plans, check what the reviewing agency means by it.
Start with the problem you’re solving
Most basins function to solve one of three problems which they need to address. The downstream system reaches its maximum capacity when peak flow occurs during post-development operations. The agency needs to keep a particular amount of runoff on their property so they focus on volume measurements. The basin needs to maintain slow water flow which helps it treat runoff before it reaches the outlet.
The answer to that question points to the type. A site that only has to match its old peak flow is a detention candidate. The site requires stormwater volume management to protect its overworked storm sewer system which needs retention and infiltration solutions. Multiple locations require both elements so the design process creates a system which combines stormwater detention for large storms with infiltration for small storms.
Soils decide more than people expect
The successful operation of retention and infiltration basins depends on how the ground behaves in their location. The soil allows water to move through it while the water table position and nearby building foundations and natural slopes exist but their measurements cannot be determined by looking at the ground surface. The survey identified a sandy area which turned out to contain a clay layer that started at two feet below the surface.
The testing process for infiltration needs to start during geotechnical work because it should occur before any basin development takes place. The process of water retention becomes simpler and cost-effective when soil shows its ability to drain water efficiently. The project needs to use detention as its fallback approach because the system fails to meet requirements. The system would undergo volume and footprint alterations because of this change. We experienced two different basin reconfigurations because the testing process started when it was already too late.
How much room you have
Basins are land hogs. The detention basin requires a larger area than the building’s front lawn because of its side slopes and the need for an access path and additional space above the planned water level. Retention basins need extra space because their water storage remains in place without leaving the area.
On a tight commercial site the question is often whether a surface basin fits at all. The system requires either underground chambers or vaults or large pipes which store water beneath the parking surface. The additional expenses of these systems include inspection requirements but they create space which would have been part of the basin area. The site plan needs a decision at this stage because it still has room for changes.
The outlet is the real design
The bowl is the easy part. The outlet decides how the basin behaves. A detention basin contains three main components which include a low-flow orifice for small storms and a weir or riser system for larger storms and an emergency spillway to handle unexpected storm events. Sizing those pieces comes from the hydrology and hydraulics work, where the inflow, the stored volume and the allowable release rate are worked out together.
The wrong outlet selection will cause basin drainage to either happen too quickly for proper operation or too slowly which leads to water retention for multiple days while the basin shows signs of distress. Plan checkers look hard at it, and the numbers should match what’s on the grading and drainage plans.
Safety, access and upkeep
A basin is a place people and animals can walk into, so side slopes, fencing and signage come up in design. Gentle slopes cost more land and make maintenance easier. Steeper walls save land and may need fencing or a retaining wall around part of the edge.
Maintenance matters as much as the design. Outlets clog, sediment builds up, vegetation overgrows, and standing water attracts mosquitoes in the wrong conditions. A basin needs an access ramp for equipment and a plan for who will clean it, and where it’s part of the water quality plan, that responsibility usually goes into a recorded agreement. Basins that no one inspects tend to turn into the thing the agency writes a notice about.
Fitting it into the rest of the site
A basin reaches to all civil set components which exist in the entire system. The system modifies pad heights and pipe base levels but it creates utility conflicts when no one verifies their existence and the system needs to connect its grading to the surrounding completed surfaces. The construction-phase work area exceeds the future basin area because stockpiles and haul roads tend to create initial damage to this location. The erosion control plan protects this area from soil compaction until the basin construction reaches completion.
The basin serves as the main water quality system which connects directly to the water quality management plan so all documents need to show matching capacity figures. Projects in Orange County need to achieve two main goals which include flood control and water quality improvement and the same basin must obtain approval from two different review authorities.
A quick way to frame the choice
The general value of both types remains equivalent because one does not hold superior worth compared to the other. The detention process operates effectively with all soil types because it creates simple conditions yet does not reduce the total amount of water runoff. Water retention systems decrease water quantity while they enable groundwater to recover but their success depends on soil composition and groundwater state and they need additional property area. The agency selects sites based on their official requirements and they evaluate soil characteristics and available space in that particular sequence.
Frequently asked questions
What is the difference between a retention basin and a detention basin?
A detention basin holds runoff temporarily and releases it slowly through an outlet, so the peak flow leaving the site stays at or below pre-development levels. A retention basin keeps part of the runoff on site, letting it soak into the ground or evaporate instead of flowing downstream. Some agencies use the terms differently, so confirm the definition with the reviewer.
How do I know which type of basin my site needs?
It depends on what the agency requires, what the soils allow and how much land you have. If the main concern is peak flow, detention usually works. If you must keep runoff volume on site, retention or infiltration is the likelier fit, and soil testing will show whether that’s possible.
Does soil type affect stormwater basin design?
Yes, more than almost any other factor. Permeable soils and a deep water table make retention and infiltration practical, while clay or shallow groundwater often push the design toward detention. Infiltration testing should happen early so the basin isn’t redrawn later.
How much land does a stormwater basin take up?
More than most teams expect, since the footprint includes side slopes, an access path and freeboard above the design water level, not just the storage volume. When space is tight, underground chambers or vaults can hold the same volume beneath parking areas, though they cost more and need inspection access.
Who maintains a stormwater basin after construction?
The property owner, typically under a recorded maintenance agreement tied to the land. Regular tasks include clearing the outlet, removing sediment, managing vegetation and inspecting the structure, and the plan should name who handles each one.
Where we start
If you’re planning a site and want to know which kind of basin fits, send us the address, the proposed building and parking layout and any soils or survey information you have. We’ll tell you which options look workable, flag the likely trouble spots and send a written fee proposal. Call (949) 482-7835.